Car Fender repair rust & paint at home Diy

Author channel Mad4Motors   10 мес. назад
765,136 views

5,062 Like   1,109 Dislike

How to Repair Rust on Your Car Without Welding (No Special Tools Needed)

Rust removal and repair. Repairing rust on your car is something that should be done quickly to prevent it from spreading. It can be easily done without welding, by using strong but inexpensive body filler. You can even paint the car yourself. Rust repair is common at the wheel wells and rocker panels of cars and in this video I show the proper and most thorough way to remove and repair rust. Products: Glass Filler: http://amzn.to/2zdSA6o Gold Filler: http://amzn.to/2xtzWTx Adhesive Remover: http://amzn.to/2zduvfU Sandpaper: http://amzn.to/2gQph2b Spot Putty: http://amzn.to/2yauidi Body Patch Mesh: http://amzn.to/2iGmSri Polish: http://amzn.to/2zcSOe2 Dust Mask: http://amzn.to/2xu4017 Sanding Block: http://amzn.to/2iaKNLM Paint: Rust Converter: http://amzn.to/2iGmFo0 Rubberized Undercoating: http://amzn.to/2hmXD9N Filler Primer: http://amzn.to/2xuIrxI Color Matching Paint: http://amzn.to/2yXBWa6 Power Tools: Rust Remover Disc: http://amzn.to/2zzXSq2 Polisher: http://amzn.to/2yT243Z → Become a ChrisFix Subscriber: http://www.youtube.com/subscription_center?add_user=paintballoo7 → Instagram: https://www.instagram.com/chrisfixit → Facebook: https://www.facebook.com/chrisfix8 → Website: http://www.ChrisFixed.com → My Channel Home Page: https://www.youtube.com/ChrisFix **If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Week** Disclaimer: Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix. This video was supported by 3M and all opinions are my own. I use 3M products for my projects so this was a perfect fit for a rust repair video!

Opel Corsa B skorodowane nadwozie

Muzyka darmowa, music: Grapes - I Dunno - http://ccmixter.org/files/grapes/16626 https://soundcloud.com/freemusicarchive-1/grapes-i-dunno Zabawa w odrdzewianie 20-letniego hebla część 2: nadwozie Proszę włączyć adnotację. W dymkach pisze jak długo elementy wytrzymały zanim znowu skorodowało. Film ma charakter przygodowy. Nie jest poradnikiem. Koszty 322zł Plastiki malowane "czarnidłem do zderzaków" trufle wax black trim Korozje malowałem preparatem Cortanin F

The TRUTH about WD 40 vs Headlights!

I had to the WD 40 vs Headlights myth to rest. I used WD 40 to clean my headlight on my truck. I felt like the Toothpaste Method for cleaning headlights was a lot of scrubbing. Here is what happened after just a few minutes of rubbing WD 40 on my Toyota Tacoma Headlights! ** Update video on WD 40 and Headlights & OFF Bug Spray vs Headlights- https://www.youtube.com/watch?v=0RprGfldXm4 Please Follow me on Facebook and Instagram @yakmotley!

Severely Neglected Wheel Restoration

Another week another severely neglected and rusty item goes onto the bench to get brought back to life! This week the item in question is a SEVERELY NEGLECTED MOTORCYCLE WHEEL that has certainly seen better days. Now before i begin the description i would like to take a moment to say this wheel is NOT going back on the road so please dont flood the comments section saying that i never used new bolts for the brake disc or torqued them down to the required lbs/ft or removed or replaced the bearings etc etc you get the idea. Also let me know what you think of the editing on this one, ive tried to cut it down and speed up the more boring sections to keep the overall time down as i know lots of you guys wont have a good hour and a half spare to watch a wheel being refurbished at normal speeds. If you think its to fast and choppy please let me know and ill revert to the longer and less choppy cuts. Anyway..... First thing is first the obligatory before close up and as you can see from it the wheel is in a very poor condition, sitting in a muddy corner for years and spiders living in the centre hub have certainly made a monster out of this once lovely wheel! The first job on the list was to get in on the tyre machine and get the beads broken to allow the shoe of the machine to lift the tyre off, then while it was clamped in the machine i thought this is a perfect time to remove the brake disc bolts while its clamped down to a solid surface as these bolts can be a right pig to remove if they have been over tightened and flooded with thread locking compound. To my surprise they broke loose fairly easily. Next on the list was getting it on the workbench and getting it torn down completely first out were the cushions for the drive sprocket (actually in very good condition for the age and the weathering they have been through!) then off the the old valve neck and wheel weights. The brake disc and bolts were then put in a DEOX C bath while i worked on the rest of the rim. To clean the surface grime and muck from the rim CONCEPT CHEMICALS MASTER CLEANER was used at a low dilution ration then agitated aggressively with a VIKAN brush after soaking for a few minutes it was time to pressure wash it clean and get a look at what i actually had to play with. It wasn't too bad but definitely did require a lot of attention to get it looking its best again! Out came the PAINT PANTHER for the next stage which was to remove the old nasty paint to reveal the lovely diamond cut alloy edges and shot peened hub and spokes, Not being a fan of polished metal it was at this point i decided on an all paint finish but at this stage i wasn't sure about colour. After a bit of wire brushing with the dremel and a good hand sanding it was time to get it masked up and into primer. First came 2 light coats of U-POL ETCH PRIMER to give the high build primer a solid base to grip onto.The HIGH SOLID HIGH BUILD PRIMER went on in three coats with sufficient time left between coats for maximum build. After that was dry a bit of wet sanding was required mostly in the centre of the wheel to eradicate the shot peening marks so that the rim would have a uniform gloss finish when done. PREPARATION IS THE KEY TO A FANTASTIC FINISH! For doing the base coat and lacquering it is necessary to make some sort of rig so that you can get at both sides of the wheel instantly, if you only try to paint one side of a wheel and then flip it over to get the other side all you end up with is one side that looks passable and the other that looks shockingly bad! Before i could begin painting it was necessary to do a few touch ups with a little aerosol primer where i had to sand quite far down to get a uniform smooth finish after that was done and dried it was time to spray my colour choice REPSOL ORANGE After the base and clear was done i took the mad notion to run a single pin stripe round and im glad i did i really like the way the silver pops out from the REPSOL ORANGE. Then it was simply a case of cleaning up a few bolts and re-assembling the wheel. If you like what you see and have any ideas for the channel please let me know in the comment section. And as usual if you liked the video please like subscribe and share this video and help the channel grow. Really Random Channel.

How to Remove Rust with Electricity

In this video, I show you how to remove rust without any effort. You can use a wire wheel to remove any rust but doing this process will remove any rust without any scrubbing, grinding, or anything else. You let it sit in the tub of water with the electrolysis process in the works, and you wipe the rust away. How to Prevent Brakes from Rusting ▶︎ https://youtu.be/xePKhHJfdho How to Paint Brake Rotors ▶︎ https://youtu.be/fMQwB1Ioutg If you have any questions regarding the video, you know where to throw them!! Thanks for watching :) ______________________________________________________________ Please give it a like 👍 and follow 👣 milanmastracci YouTube Channel ▶︎ https://www.youtube.com/user/milanmastracci/ milanmastracci Facebook Page ▶︎ https://www.facebook.com/milanmastracci/ milmast Instagram ▶︎ https://instagram.com/milmast/ ______________________________________________________________ Videos in the Outro 🎥 How to Blackout Your Headlight Housing ▶︎ https://youtu.be/jhCc98AuXg4 Can you Dip Emblems on a Dipped Car ▶︎ https://youtu.be/oWtbzony9jg ______________________________________________________________

Step by step guide on how to repair rust at home with little cost.

East diy job you can do on your own car with great results!

Facebook- https://www.facebook.com/Mad4Motors

Disclaimer:
Due to factors beyond the control of Mad4Motors, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Mad4Motors assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair video's. Due to factors beyond the control of Mad4Motors, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Mad4Motors.

Comments for video: